![]() ![]() e1000e: Intel(R) PRO/1000 Network Driver Subsystem: Lenovo Ethernet Connection (2) I219-LM Supported link modes: 10baseT/Half 10baseT/FullĪdvertised link modes: 10baseT/Half 10baseT/FullĠ0:1f.6 Ethernet controller : Intel Corporation Ethernet Connection (2) I219-LM (rev 31) Oct 18 23:10:52 pve systemd: wol.service: Succeeded. Oct 18 23:10:52 pve systemd: Started Wake-on-LAN for eno1. Main PID: 950 (code=exited, status=0/SUCCESS) Process: 955 ExecStop=/sbin/ethtool -s eno1 wol g (code=exited, status=0/SUCCESS) Process: 950 ExecStart=/sbin/ethtool -s eno1 wol g (code=exited, status=0/SUCCESS) Loaded: loaded (/etc/systemd/system/wol.service enabled vendor preset: enabled)Īctive: inactive (dead) since Mon 23:10:52 CEST 1min 57s ago Sudo chmod 755 /etc/rc0.d/wol_poweroff.sh & sudo chmod 755 /etc/rc6.d/wol_poweroff.sh Created script to bring the ethernet interface down properly at shutdown :Ĭp /etc/rc6.d/wol_poweroff.sh /etc/ rc0.d/wol_poweroff.shįinally changed permissions to make it executable: I tried sending packets to the combination of host's MAC and IP (as well as broadcast to 255.255.255.255), ports 7,9,4343,4000,etc.When the machine is powered off, and I send magic packets using apps like "wol" (from a windows host), an android app (landroid), I understand that they are reaching the NIC as I can see the ethernet port flashing, but the machine doesn't boot.When the machine is powered on, I successfully tested receiving magic packets using netcat.I also created a systemd service " wol.service", to also set the eno1 interface's wol to "g", using ethtool (see #3 below).Created script to bring the ethernet interface eno1 down properly at shutdown, based on this bug (see #2 below).Updated cat /etc/network/interfaces so that at every boot, it sets the vmbr0 interface's wol to "g", using ethtool (see #1 below).The NIC supports WoL and is (/was already correctly) enabled and set to "g".The BIOS (is up-to-date) supports WoL and is enabled.At this point I am not sure if it is a configuration issue or a BUG? I can't get Wake on Lan (WOL) to work with Proxmox, no matter what. I then installed Proxmox 7 (5.11.22-4-pve) on the same hardware. I was able to wake up the system from a "Hibernate" or "Sleep" mode by sending a magic packet from another windows host. disable "reduce speed on power down") and the UEFI BIOS to make it work. I had to make some changes in the adapter settings (eg. Since it is inside the LAN, it's close to guaranteed that the WoL will work.I confirmed that Wake On Lan works with Windows 10 Pr o on a Lenovo ThinkStation P310 with onboard Intel I219-LM GB Ethernet controller. I use a Raspberry Pi as a WoL "platform" - the router has a port forward to the Pi's ssh server, so I ssh to the Raspberry Pi and send the magic packet from there. dd-wrt can be used to send the magic packet from within your network, and since it is always on, you won't need more hardware online 24/7. Or, if your router is supported, check out dd-wrt and flash your router if you're comfortable with it. For example, being able to ssh (or telnet, but that's dangerous) to your router and send the magic packet from there. Since it looks like Internet WoL is unreliable, as you will depend on intermediate routers allowing it, you are probably safer if you find something in your network you may use to do the WoL for you. However, your router needs to allow the forwarding of packets to the broadcast MAC address, or your computer's WoL system needs to be more flexible, such as accepting WoL addressed to its own MAC address (I actually thought this was the standard approach, but Wikipedia says I'm wrong). contains anywhere in the payload the magic string (6x FF and 16x computer's MAC address). ![]() ![]() is addressed to the broadcast MAC address, and.However, I've been told more than once that, to my surprise, any packet received by the computer's NIC may be a magic packet if it ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |